printer-20220829_004721.cfg

###Anycubic Vyper Klipper Config###

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA7
position_min: -3
position_endstop: -3
position_max: 245
homing_speed: 30.0

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC13
microsteps: 16
rotation_distance: 32
endstop_pin: !PC5
position_min: -17
position_endstop: -17
position_max: 245
homing_speed: 30.0

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC14
microsteps: 16
rotation_distance: 8
endstop_pin: PB2
position_endstop: 0.0
position_max: 260
position_min: -3
homing_speed: 5.0

[stepper_z1]
step_pin: PC0
dir_pin: !PC1
enable_pin: !PC15
microsteps: 16
rotation_distance: 8
#endstop_pin: PC6


[thermistor T-D500]
temperature1: 100
resistance1: 120000
temperature2: 200
resistance2: 6800
temperature3: 288
resistance3: 1066


[extruder]
step_pin: PB4
dir_pin: !PB3
enable_pin: !PA15
microsteps: 16
rotation_distance: 7.6555
nozzle_diameter: 0.600
filament_diameter: 1.750
heater_pin: PA1
sensor_type: T-D500
sensor_pin: PC4
control: pid
pid_kp = 28.937
pid_ki = 1.295
pid_kd = 161.688
min_temp: -70
max_temp: 320
pressure_advance = 0.4764

[heater_fan extruder_fan]
pin: PB1
off_below: 1.0

[heater_bed]
heater_pin: PA4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PB0
control: pid
pid_kp = 67.648
pid_ki = 1.044
pid_kd = 1095.893
min_temp: 0
max_temp: 110

[fan]
pin: PA0

[probe]
pin: !PB12
#z_offset: 0
activate_gcode:
    probe_reset

[output_pin LED]
pin: mcu:PA13
pwm: False
value: 0

[output_pin probe_reset_pin]
pin: PB13

[bed_mesh]
mesh_min: 15,15
mesh_max: 230, 230
probe_count: 5,5
algorithm: bicubic
speed: 40

[filament_switch_sensor runout]
pause_on_runout: True
switch_pin: PA5

[mcu]
serial: /dev/ttyUSB0
restart_method: command

[temperature_sensor Raspberry Pi]
sensor_type: temperature_host
min_temp: 0
max_temp: 100

[safe_z_home]
home_xy_position: -3,-17
z_hop: 10

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_accel_to_decel: 3000
max_z_velocity: 5
max_z_accel: 100

[gcode_macro probe_reset]
gcode:
    SET_PIN PIN=probe_reset_pin VALUE=0
    G4 P300
    SET_PIN PIN=probe_reset_pin VALUE=1
    G4 P100

[virtual_sdcard]
path: ~/gcode_files

[display_status]

[pause_resume]

[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
gcode:
    ##### set defaults #####
    {% set x = params.X|default(230) %}      #edit to your park position
    {% set y = params.Y|default(230) %}      #edit to your park position
    {% set z = params.Z|default(10)|float %} #edit to your park position
    {% set e = params.E|default(1) %}        #edit to your retract length
    ##### calculate save lift position #####
    {% set max_z = printer.toolhead.axis_maximum.z|float %}
    {% set act_z = printer.toolhead.position.z|float %}
    {% set lift_z = z|abs %}
    {% if act_z < (max_z - lift_z) %}
        {% set z_safe = lift_z %}
    {% else %}
        {% set z_safe = max_z - act_z %}
    {% endif %}
    ##### end of definitions #####
    PAUSE_BASE
    G91
    {% if printer.extruder.can_extrude|lower == 'true' %}
      G1 E-{e} F2100
    {% else %}
      {action_respond_info("Extruder not hot enough")}
    {% endif %}
    {% if "xyz" in printer.toolhead.homed_axes %}    
      G1 Z{z_safe}
      G90
      G1 X{x} Y{y} F6000
    {% else %}
      {action_respond_info("Printer not homed")}
    {% endif %}

[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
gcode:
    ##### set defaults #####
    {% set e = params.E|default(1) %} #edit to your retract length
    #### get VELOCITY parameter if specified ####
    {% if 'VELOCITY' in params|upper %}
      {% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
    {%else %}
      {% set get_params = "" %}
    {% endif %}
    ##### end of definitions #####
    G91
    {% if printer.extruder.can_extrude|lower == 'true' %}
      G1 E{e} F2100
    {% else %}
      {action_respond_info("Extruder not hot enough")}
    {% endif %}  
    RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
    TURN_OFF_HEATERS
    CANCEL_PRINT_BASE

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [probe]
#*# z_offset = -0.430