-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathMKS_DLC32_2_CoreXY_Solenoid.yaml
126 lines (105 loc) · 2.23 KB
/
MKS_DLC32_2_CoreXY_Solenoid.yaml
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
board: MKS-DLC32 V2.1
name: Ladybug Plotter
meta: (23.03.2024) by Inva
stepping:
engine: I2S_STATIC
idle_ms: 0
pulse_us: 4
dir_delay_us: 1
disable_delay_us: 0
kinematics:
corexy:
axes:
x:
steps_per_mm: 80.48
max_rate_mm_per_min: 14000.000
acceleration_mm_per_sec2: 1500.000
max_travel_mm: 525.000
soft_limits: false
homing:
cycle: 1
positive_direction: false
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 3000.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: gpio.36:low
hard_limits: false
pulloff_mm: 4.000
stepstick:
step_pin: I2SO.1
direction_pin: I2SO.2:low
y:
steps_per_mm: 80.48
max_rate_mm_per_min: 14000.000
acceleration_mm_per_sec2: 1500.000
max_travel_mm: 1000.000
soft_limits: false
homing:
cycle: 2
positive_direction: false
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 3000.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: gpio.35:low
hard_limits: false
pulloff_mm: 4.000
stepstick:
step_pin: I2SO.5
direction_pin: I2SO.6:high
z:
steps_per_mm: 80
max_rate_mm_per_min: 64000
acceleration_mm_per_sec2: 4800
max_travel_mm: 15
motor0:
solenoid:
output_pin: gpio.32
pwm_hz: 100000
off_percent: 0.000
pull_percent: 100.000
hold_percent: 85.0
pull_ms: 50
direction_invert: false
i2so:
bck_pin: gpio.16
data_pin: gpio.21
ws_pin: gpio.17
spi:
miso_pin: gpio.12
mosi_pin: gpio.13
sck_pin: gpio.14
sdcard:
cs_pin: gpio.15
card_detect_pin: NO_PIN
control:
safety_door_pin: NO_PIN
reset_pin: NO_PIN
feed_hold_pin: NO_PIN
cycle_start_pin: NO_PIN
macro0_pin: gpio.33:low:pu
macro1_pin: NO_PIN
macro2_pin: NO_PIN
macro3_pin: NO_PIN
macros:
startup_line0:
startup_line1:
macro0: $SD/Run=lasertest.gcode
macro1: $SD/Run=home.gcode
macro2:
macro3:
coolant:
flood_pin: NO_PIN
mist_pin: NO_PIN
delay_ms: 0
start:
must_home: false
# 5,18,19,22,23,25,26,27,32,33,39,I2SO.7
# SDA 0 / SCL 4