Behringer Cmd Studio 4A

Behringer CMD Studio 4a

The Behringer CMD Studio 4a is a 2 deck controller that supports 4 virtual decks.

• Mixxx Forum Thread
• Manufacturer's product page
• Manufacturer's manual

Mixxx Sound Hardware Preferences

• Master output: channels 1-2
• Headphone output: channels 3-4

Controller Guide

Most of the buttons and knobs on the controller behave as you would expect:

The only major departure form the above are the 4 "FX Control" knobs and buttons at the top of each deck.

Mixer

• The deck faders, cross-fader, master, and headphone monitoring (mix & volume) knobs all operate as you would expect.
• Each deck also has a (pre)gain knob (leftmost "FX Control" knob).

Navigation Control

• The BROWSE knob scrolls thorough the track list in the library panel.
• The left and right buttons move through the library tree.
• The ENTER button expands/collapses library tree items.

Hot Cue Buttons

• If not currently set, pressing a HOT CUE button sets that hot-cue at the current playback position.
• If already set, pressing a HOT CUE button jumps to that HOT CUE position.
• Pressing DEL toggles DELETE-mode.
• If DELETE-mode is active, pressing an already set HOT CUE button will clear that hot-cue.

 * The main function of the DEL button is to toggle DELETE-mode to allow HOT-CUES to be cleared, however DELETE mode also alters some of the other button functions (see below).

Deck Select Buttons

• The deck select buttons (A, B, C, D) make the respective "virtual" deck active.
• On the left deck: A = Channel 1, C = Channel 3.
• On the right deck: B = Channel 2, D = Channel 4.

Transport Control

• The LOAD buttons will load the currently highlighted track in the library window into that deck.
• The deck CUE, PLAY, SYNC, and LOOP buttons work as you would expect in Mixxx, (SYNC toggles master sync mode).
• The deck wheels work as you would expect, (including the touch sensitive platter changing the behaviour in both SCRATCH and JOG modes).
• When DELETE-mode is active (see above) the PLAY button triggers reverse playback instead of the usual function.

Additionally:

• FX Control button 1 toggles the deck slip mode on/off.
• FX Control button 2 toggles the deck repeat mode.
• FX Control button 3 can be tapped to adjust the beat-grid position.
• FX Control button 4 toggles the deck quantise mode on/off.

Playback Pitch/Rate

• The pitch sliders operate as you would expect.
• The PITCH BEND buttons step the playback rate up or down.
• The LOCK buttons lock the key so the pitch doesn't change when the playback rate changes (as you would expect).
• If DELETE-mode is active the PITCH BEND buttons step the key up/down without altering the playback rate.
• If both PITCH BEND buttons are pressed together, the playback rate (or key if DELETE-mode is active) are reset to their normal value.
• The PITCH BEND buttons will indicate whether the current pitch is higher or lower than normal for that track.

3-Band EQ and Kill Buttons

• The HIGH, MID, and LOW knobs (and kill buttons) operate as you would expect.

FX

• The "Quick Effect" filter on each deck is assigned to rightmost "FX Control" knob.
• The 2 FX ASSIGN buttons on each deck send the deck's output to one (or both) of two effects in the (default) 4-unit effects rack. The left deck (A or C) can be assigned to effect units 1 and/or 2. The right deck (B or D) can be assigned to effect units 3 and/or 4.
• The middle two "FX Control" knobs on each deck act as the effect "super" controls for each of the two effects that the deck can be assigned to, (most effects should respond sensibly to these controls).