-
Notifications
You must be signed in to change notification settings - Fork 90
Rev 3 BOM
TomWhitwell edited this page Aug 29, 2017
·
2 revisions
All the parts are relatively straightforward once you have the Eurorack specific sockets and vertical pots - both available from Thonk. The only tricky and critical part in Europe is the vertical SD Card Reader from Yamaichi, which I've only found available in small numbers from Acme in Italy. This part is available in the US from Mouser as part 945-PJS008U-3000-0.
NB: You will also need:
- Micro-B USB Cable - a Kindle cable works fine
- MicroSD card, up to 32gb. Teensy developer Paul Stoffregen recommends Sandisk Ultra MicroSD cards
Button colours:
- White 611-D6R00F1LFS
- Grey 611-D6R10F1LFS
- Yellow 611-D6R30F1LFS
- Red 611-D6R40F1LFS
- Green 611-D6R50F1LFS
- Blue 611-D6R60F1LFS
- Black 611-D6R90LFS
Previously it was stated that using 100k pots is ok, but it was found in testing that this could lead to CV instability.
Qty | Value | Device | Parts | Mouser Part # |
---|---|---|---|---|
1 | 5 x 2 Power Header | SV1 | 649-67997-210HLF | |
2 | 1N4001 | 1N4001 Diode | D5, D6 | 512-1N4001 |
1 | 50K | Bourns 3362P Trimmer | Output level | 652-3362P-1-503LF |
1 | 78L05 | 78L05 TO92 5v 100ma voltage regulator | IC3 | 512-LM78L05ACZ |
2 | 50k Linear | ALPHA 9mm Vertical pots (see note above on 100k pots) | CHANNEL-POT, TIME-POT | Thonk, Bitsbox, Smallbear |
6 | BAT42 | BAT42 Schottky Diode (or other, or 1N4148) | D1, D2, D3, D4, D7, D8 | 78-BAT42-TAP |
2 | BL01RN1A | BL01RN1A Ferrite Bead (or 10R Resistor) | L1, L2 | 81-BL01RN1A1D2B |
2 | 100n | Ceramic Cap | C5, C8 | 594-K104K15X7RF5UH5 |
2 | 1n | Ceramic Cap | C1, C4 | 594-K102J15C0GF5TH5 |
2 | 100n | Poly Box Cap | C2, C3 | 80-R82DC3100AA50J |
2 | 10uf | Electrolytic Cap | C6, C7 | Panasonic ECE-A1EKS100 |
1 | C&K D6 SPST Momentary Key Switches | RESET | 611-D6R60F1LFS | |
5 | 3mm LEDs | LED1, LED2, LED3, LED4, LED5 | 604-WP710A10ID | |
2 | 40 pins (cut to fit) | 36 Pin Male Header | 649-68000-436HLF | |
2 | 36 pins (cut to fit) | 36 pin Female Header | 517-929974-01-36-RK | |
2 | FUSE | 200ma PTC Poly Fuse | F1, F2 | 652-MFR020-LF |
1 | 100k | 1/4W Resistor | R19 | 660-MF1/4LCT52R104G |
2 | 22k | 1/4W Resistor | R10, R21 | tbc |
1 | 10k | 1/4W Resistor | R8 | 660-MF1/4DCT52A1002F |
3 | 1K | 1/4W Resistor | R7, R1, R2 | 660-MF1/4DCT52R1001F |
5 | 1.5k | 1/4W Resistor | R11, R12, R13, R14, R15 | tbc |
2 | 47k | 1/4W Resistor | R9, R20 | |
2 | 220R | 1/4W Resistor | R17, R18 | 660-MF1/4DCT52R2200F |
1 | 330K | 1/4W Resistor | R5 | 660-MF1/4DCT52R3303F |
2 | 8.2k | 1/4W Resistor | R3, R4 | 660-MF1/4DCT52R8201F |
1 | Teensy 3.1 | U1 | pjrc.com, Cool Components or OSHPark | |
Pins or stackable long pins for Teensy | ||||
1 | 14 pin IC Socket | 649-DILB14P-223TLF | ||
1 | TL074 | TL074 Quad Op Amp | IC4 | 595-TL074CN |
1 | YAMAICHI PJS008U-3000-0 | Vertical SD Card Holder | Thonk, MSD-HOLDER-3: www.acmesystems.it/catalog_sdcard | |
4 | Thonkiconn Socket | Available from Thonk |
Table created at: http://www.tablesgenerator.com/markdown_tables
- Parts List
- Preparing your Teensy 3.1 or 3.2
- Formatting and setting up the SD Card
- Building the module
- Testing and calibration
- Troubleshooting and FAQ
- PCB Versions
- Schematics